changed out all parts listed unit checked out

checked unit out reset controls floor in house is very soft cust to put 3/4 inch ply wood under unit to support unit and back off on load size unit checked out

"Upon arrival I found burner not coming on, will need a burner and control. ; ordrng 1 W11517959 (Left burner) and 1 W11747115 (Control board)"

"Upon arrival I was missing one part that I forgot to order, I explained to costumer that I take full accountability for not ordering the float switch. ; ordrng 1 WPW10346525 (Float switch) and 1 WPW10195039 (Switch)"

"I replaced fan, control board, panel, interlock switches, fan capacitor"

Unit runs but doesnt heat. Customer has 120 volts on L1 and 85 volts on L2 no220 across L1and L2. Customer has house hold wiring issues

Ran diagnostic ordering control ; ordrng 1 W11608056 (Control)

"Ran diagnostic replace faulty drain pump, all functions checked okay"

Inspected and fouynd washer outer TUB with a hole underneath leaking during FILL Will ned TUB ; ordrng 1 W10371566 (Outer TUB)

Replaced recirculatimg pump

"Replaced valve, couplings, tubing, condenser fan motor and blade. Operation are correct now; used 1 2300868 (Coupling), and 1 W10271543 (Coupling) from stock"

"replaced control, element, thermistor, and thermal cut off. unit tested ok."

"Upon arrival we noticed the compressor turned on this time, but the evaporator coils was still not cooling. Will need the Evap ; ordrng 1 WPW10218037 (EVAP)"

"Upon arrival I replaced parts and found out the unit needs a start button, tested it and the start button is broken. ; ordrng 1 W11230930 (Start button)"

"Upon arrival costumer experienced no heating, I found unit not heating and will need a burner gas ; ordrng 1 W11652257 (Burner gas)"

"Upon arrival I replaced all components and it is now washing, unit is working as designed."

Replaced shorted capacitor ran and tested unit checks ok

Replaced panel ran and tested unit checks ok

Replaced shorted wash motor ran and tested unit checks ok

Sll unit functions checked ok. Ordering Lower back panel 30 days cosmetic ; ordrng 1 W11730240 (Lower panel)

"Ran diagnostic, all unit functions checked ok at this time. Customer advised on unit functions and care."

Unable to contact customer ; saved tckt

Ran diagnostic ordering replacement Icemaker ; ordrng 1 W11658802 (Icemaker)

"replaced ice maker, valve and cover. unit tested ok. advised cust about filter, and supply valve."

"Upon arrival and after replacing the parts, I then ran a quick wash cycle and let it run from beginning to end. The unit completed the quick wash cycle with no issues and then I ran a diagnostic test and it also passed with no issues. Unit is working properly as designed."

"Upon arrival and diagnosing with tech line per Techline, the moisture on the gasket is going to be normal. I did adjust the freezer door a bit more but thats about it. I did find different readings on the million but per tech line. He said it is normal readings. Another factor Techline mentioned was the temp in the house should be cooler to help with the moisture. 7740383173"

Upon arrival and after running a full diagnostics I could not find an issue. I saw no error codes and then ran a diagnostic cycle it also passed with no issues. The customer mentioned it would happen in the beginning of a cycle and I explained how the unit is sensing the load at that point and that is what they are hearing. The unit it self is working properly as designed.

"Upon arrival and after installing the parts, the damper control no longer made sounds. I tested the damper control through service test#3 and it open and closed with no issue. The unit is now working properly as designed."

Removed left refrigerator door. Replaced top hinge on door. Operations are correct now

needs trans; ordrng 1 w10834890 and 1 w11164183 and 1 w10808317 and 1 w10550173 and 2 357640s and 1 w11398781

Checked unit and replaced misformed freezed door slides and brackets. Unit checks ok.

Unit working now. All burners and bake turning on. The electrician told me the issue was with the outlet.

"During service, two error codes were found on the washer: F7E1 (Tachometer Missing) and F0E3 (Overload). Upon inspection, the protective shield and drive belt were discovered underneath the unit. The issue appears to have been caused by an overload condition that caused the basket to drop low enough to contact the floor, dislodging both the shield and the belt. With the belt off, the drum could not rotate, resulting in the F7E1 error due to the missing tachometer signal. After consulting with Whirlpool Techline (SR# 7741576519) and documenting the findings, the belt was replaced. Its likely the weight of the drum pressing down on the motor belt and the continued strain during operation caused the belt to lose elasticity and slip off. After replacing the belt, a full diagnostic test cycle was completed, during which the drum and basket remained properly positioned, and the unit functioned normally with no further errors. Per Techline no parts issue or replacement needed working as design - if you wish for additional information you can contact your extended warranty or whirlpool customer service and use the SR# as a reference."

Unable to replicate issue - unit working as design

unit needs control board and capacitor ; ordrng 1 W11608056 (CNTRL-ELEC) and 1 W11428524 (CAPACITOR)

"Replace heater, evap motor and thermistor - unit operating as normal"

"Checked unit and replaced open harness, shorted controls and thermistor. Unit checks ok."

"Found faulty gearcase, slider and stator. Leaking oil from gearcase caused slippage between the slider and the stator. This stripped the splines on both parts quoted customer for repair. Customer declined repair as it is not ecologically feasible"

Replace modules Special Project S84638 -

"Ran diagnostics, removed off balance errors and adjusted leveling. All functions checked ok at this time"

"Ran diagnostics, replaced complete harness assembly in unit. All functions checked ok"

"Ran diagnostics, replaced start device and capacitor assembly. All functions checked ok at this time. Customer to monitor"

"Ran diagnostics, replaced complete freezer door in unit. All functions checked ok at this time"

"Ran diagnostics, replaced complete harness assembly in unit once more. All func checked ok at this time ; used 1 W11643701 (Harness) from stock"

"Will need water valve, filter housing and water level sensor. ; ordrng 1 W10897719 (Water valve) and 1 W11542867 (Pump with sensor) and 1 W11266112 (Filter housing)"

Ran diagnostic and compressor not coming on. Will need seal system components. ; ordrng 1 WPW10608485 (Evaporator) and 1 WPW10466675 (Compressor) and 1 WPW10143759 (Filter drier)

Found bad gearcase. Customer denied repairs.

Replaced cracked blower wheel & motor. Per Techline replace wheel housing. SR#7741579171; ordrng 1 Wpw10211911 (Housing) and 1 Wpw10342188 (Pipe) and 1 W11234001 (Motor) and 1 W11327190 (Wheel)

Checked unit in diagnostics ice maker is filling with water sensor are working properly fill tube heater is working advised customer to replace water filter

"Upon arrival, I inspected the unit and found no power coming into the unit. The Breaker was off, and the customer was okay to turn the Breaker back on. Tested unit after working as designed"

"Upon arrival, I inspected the unit and found that the fan switch and harness need to be replaced. SR 7741570967.Sr7741576139 submitted findings to safety, harnesses are unrepairable"

Replaced main console

"Need stator motor; ordrng 1 W10897050 (Stator, Motor) and 1 W10897040Rotor,Motor (Rotor, Motor)"

"Need evaporator and drier ; ordrng 1 W11394386 (Assembly, Evaporator) and 1 W10805035 (Drier)"

Replaced drain pump

Found door unlock failure f5 e3 error adjust latch ran recalibration cycle ran diagnostics all test normal.

Replaced both tubes housing and container. Unit is OK.

Order parts ; ordrng 1 Wp3387747 (Element) and 1 Wp3387233 (Sensor) and 1 W10909685 (Fuse) and 1 Wp8577274 (Thermistor) and 1 Wp8557403 (Stat) and 1 280148 (Cutoff) and 1 W11388032 (Control)

Check unit to find defective left rear and left front element and switches. Technician presented customer with an estimate and she is on undecided.

Replace defective gear case harness and cam unit is now working properly. There is a new labor code on the document pictures.

"Check unit to find all operations working as design. Customer was informed that she is using too much soap, causing excessive soap buildup, which causes the drain pump to run longer. She was informed to run a clean washer cycle before trying to use the unit again for washing clothes, unit is OK."

Check unit at fix loose connection at drain pump. Customer broke the wires and denies unit is OK.

Replaced defective motor unit is ok

Check unit and replace defective control. Unit is not working properly.

Check unit to find all operations working properly. Customer was informed that she has obstruction inside the wall and a major blockage for the exhaust. Flow test results are on the document picture and technician also showed customer the blockage on the roof. There is also a picture of that on the document she needs a professional duct cleaning provider unit is OK.

Found dry working as design main event that run outside the building the cover is painted over

Replace defective elements all tested OK

Replace defective gasket on both sides unit working OK now no issues to report

Found defected switch/element replaced same parts . Everything tested OK

Upon arrival I diagnosed unit. Unit has power coming in but doesnt do nothing panel ui unresponsive. Will need parts order.; ordrng 1 W11116422 (Panel) and 1 W11402115 (Control Ui) and 1 W11306302 (Control Board)

Upon arrival i diagnosed unit. No error codes found i ran diagnostic cycle unit completed normally. I couldnt duplicate customers concern. Customer mention it only happends when towels or bedding. I made customer aware the importance of distributing the weight evenly. If not it can cause banging noises especially during spin (picture attached) of load 1 item dog bedding. Unit is working as designed. SR#7741581344.

Ran diagnostic and there is no error codes and heater is coming on. I explained to customer to use rinse aid because she stopped using it about a month ago.

"this is a different no power the 1st time replaced hub and all function ok; used 1 W11481722 (ACTUATOR), and 1 W10528947 (HUB) from stock"

"Issue had nothing to do with cooling. The unit is cooling property. The freezer door gasket was off, I reattached it and sent a quote to the customer for replacing the freezer door gasket ; ordrng 1 W11574983 (Freezer door gasket)"

Ran the unit through service test mode 120 for the icemaker diagnostic cycle and it threw a error code the first time saying that the ice bin was full and then after running it a second time it kept on throwing cannot find the end of harvest location. Also tried to run the fill test and could not get the icemaker to fill up even after running the filter tube heater for about two minutes need to replace the filter tube heater along with the icemaker; ordrng 1 W11391031 (Icemaker assembly) and 1 W11365533 (Icemaker fill tube with heater)

Freezer temperature was only 28?. The customers meat was not even frozen solid. All of their stuff was slowly falling out already and the refrigerator is only a week old. Ran the unit through diagnostics test. Everything was checking out. Good compressor was running exchanging heat when checking the evaporator panel the evaporator has a clog on about the fourth run going up the evaporatorNeed to replace the compressor and evaporator; ordrng 1 W11357918 (Evaporator) and 1 W11358352 (Compressor)

"The arm extension at the top of the refrigerator door that hits the door switch to the refrigerator was broken due to the bolt being snapped off inside of the threads so the door switch was constantly open, and the unit would not make ice or lights would not work properlyand the door alarm was constantly flashing red I told the customer that we could order some parts for it and he was also worried about the freezer door because it did not close very good and while looking at the bottom of the freezer door, the whole bottom of it was rusting out and starting to warp because it was deteriorate Customer did not want to follow through with any part orders. He asked me to just tape the door switch shut at the top to keep it making ice at the moment until he can go out and buy a new one closing ticket out for trip and diagnostic."

Washing machine would not start due to the lid lock being stuck in the lock position had to manually unlock it to get the door open and then found wires that were not plugged in properly and had came out of the plastic connector plugged wires back in properly and their proper spots and placeshooked everything back up and unit is unlocking and locking all operations. OK unit is operating as designed now.

Fixed loose connection to dispenser.

Ran diagnostics.

Checked unit. Fixed loose connection to valve.

Ran diagnostics. Customer not using rinse aid.

Part is covered. ; ordrng 1 W11449303 (UI)

Replace tub tested unit no leaks unit tested properly

Came out to replace dispenser motor found old motor want release from shaft old motor is rusted an seized together with shaft ; ordrng 1 LW10318289 (Freezer door)

Replace parts unit tested properly advised customer

Replaced ice maker

Deleted code history and reset control boardTested Both ovens and both reachd temperatures without any codes or issues

Replaced pump and control board

ran gas check with detector. unit is not leaking. adjusted igniter position. gas smell is only when oven is first lit. this is completely normal. advised cust on using broiler as storage. unit tested ok.

Motor not turning on ordering parts; ordrng 1 W11525546 (Pump and motor) and 1 W11516221 (Control)

Replaced parts screen is lighting up and unit is working as designed

Service was cancelled at the door

Checked unit wasnt cooling compressor was running replaced filter drier recharge unit with 47 grams of R600 unit is now cooling

Found door unlock failure f5 e3 error adjust latch ran recalibration cycle ran diagnostics all test normal.

igniter harness connection at spark mdl loose - reattached and tested - working as design

I secured loose connection at drain pump.

Fixed loose connection to control.

loose igniter harness at spark mdl - reattached and tested - operating as normal

Cleared blockage at valve screens.