Order parts ; ordrng 1 W10464673 (Motor)

checked unit out ran unit to 350 unit had good temps unit checked out

order part; ordrng 1 W11620706 (control panel)

reset breaker and rebooted control board and checked all operations. ck ok

Found faulty valve part order ; ordrng 1 W11165546 (Valve)

Replaced bad main board

No power at all; ordrng 1 W11314470 (Console) and 1 W11461188 (Control) and 1 W10693363 (Fuse) and 1 280148 (Cut off) and 1 W10396034 (Motor) and 1 W11233966 (Switch assembly)

"Ran diagnostics, ordering replacement evap motor assembly and bringing out data loggers for temperature readings.; ordrng 1 W11631626 (Evap motor)"

Unit has been exchanged

"Inspected and found motor pulley spinning but not turning Also belt is about to tear apart, will order new one Will also need cut off and thermal fuse ; ordrng 1 279827 (Motor) and 1 341241 (Belt) and 1 W10900067 (Cut off) and 1 WP3392519 (Thermal fuse)"

checked unit out glass was broke on bulb got glass out put new bulb in unit checked out; used 1 W11520384 (BULB) from stock

Checked unit out belt was not on clutch and motor put belt back on unit working as designed

adjusted simmer flames on all burners and checked operations. ck ok

replaced broken left rear leveling leg and releveled unit and checked operation. ck ok; used 1 W11025920 (LEVELING FEET) from stock

Upon arrival i diagnosed unit. After inspection noise coming from debris inside blower wheel. I removed plastic in blower wheel. I tested unit afterwards no more noise out of the norm. Unit is working as designed.

Customer approved parts. ; ordrng 1 WPW10300022 (ICE MAKER) and 1 W10838084 (ICE MAKER HARNESS)

Closing out for trip and diagnostics.

Found blower motor wire loose connection

Unable to source parts

Replaced thermostat from stock ; used 1 WP661566 (DW Thermostat) from stock

"Diagnosed dryer not heating properly. Cleared lint obstruction between blower and vent duct leaving the home, blocking airflow. Operations are now correct."

replaced broken lid strike and checked operations. ck ok; used 1 W10837741 (STRIKE) from stock

Closing out for trip and diagnostics. Unit will be replaced.

reattached loose drain pump connection - tested operating as normal

Ran diagnostics. Found disposal plug in. Customer will get plumber.

Adjusted vent baffle all tested normal.

"Uninstall and reinstall - replaced mag, trans and diode - operating as design"

"Part failure - reorder spring, hinges and bushings ; ordrng 2 WPW10337934 (Spring)s and 2 WP8268990 (Bushing)s and 1 W11612303 (Door Hinge) and 1 W11612302 (Door Hinge)"

"ran diagnostics test cycle, unit able to engage and disengage basket as normal, no error code or part failure - operating as design"

Replace damper control and tested - working as design

"Upon arrival costumer experienced a noise while spin, after diagnosing, it will need a blower wheel, a motor, and a belt. ; ordrng 1 279827 (Motor) and 1 341241 (Belt) and 1 WP694089 (Blower wheel)"

"Upon arrival, I tested control board for voltage to see if the pump n motor was receiving power, it was not and the fuse was open, it will need a control board and pump n motor. ; ordrng 1 W10866116 (Control board) and 1 WPW10455261 (Pump n motor)"

"Both of the convection fans in the big oven section are just constantly running without even turning the unit on and there is an electrical burning smell coming from the unit after the fans run for a few minutes then once I turn the oven on and ran it for about two minutes and It started getting warm. The smell started to increase. I turned on the oven light on the panel and then the oven light would not turn off, but the button was still clicking and making the noise that I was hitting the button, but would not turn the light off. Need to replace the main control boards along with both convection fans.; saved tckt"

"F7E4 basket re-engagement failureF6E3 ACU Lost communication to the MCU F0E5 Off-balance load picked up during diagnostic cycle with nothing in itChecked underneath the washer due to loud grinding noise, the stater is rubbing on the rotor, and the magnets have created a black dust around the frame of the unit and the transmission is also dripping water/oil Need to replace everything from top to bottom main control board, spin basket, outer tub, transmission, slider, stater, rotor, and the drain pump Spain or not so corroded, most likely wont come off ; ordrng 1 W11266006 (Main control) and 1 W11094304 (Tub ring outer) and 1 W10625252 (Agitator screw) and 1 W10834917 (Agitator plate) and 1 W11178227 (Spin basket) and 1 W11183985 (Spanner nut) and 1 W11219115 (Outer tub) and 1 W11187091 (Suspension rods) and 1 W11130936 (Lower wire harness) and 1 W11089264 (Drain pump filter) and 1 W11185701 (Transmission) and 1 W11218170 (Transmission washer) and 1 W10006483 (Stater) and 1 W10905022 (Clutch) and 8 W10644129 (Stater screws)s and 1 W10905025 (Slider) and 1 W10006482 (Stater cover) and 1 W11263349 (Drain pump) and 1 W11096267 (Water valve) and 1 W10921681 (Cleaner wipes)"

"Washing machine user interface is not powering on to click any of the buttons or to do anything check the wall plug polarity is good and have 120 V and theres 120 V going in to the board both of the yellow lights on the user interface and main control are both on, but theres no functions happeningNeed to replace the main control board along with the user interface and the lid strike because it is brokenNeed to see if customer would like to follow through with repairs subtract what he has already paid off of the total cost of the ticket; ordrng 1 W11479877 (Main control board) and 1 W11130428 (Panel user interface) and 1 W11091027 (Lid strike)"

"Right burner knob was working properly on and off, but when it was at its home position of off, it was not lined up. It was crooked, so I had to take the front panel off along with all the burner knobs and housings and adjust the gas valve position after putting everything back together the burner knob works properly and is sitting flush and its position with all the other knobsAll operations OK unit operating properly now"

"Installed the parts ran the unit through a diagnostic cycle all operations OK it is operating as design now all of the wires have plenty of slack and I also advised the customer to make sure shes not overloading the unit causing it to shake more than it should so that the wires dont have a chance of breaking or pulling too tight, causing them to snap when it shakes"

"Lower dish rack, broken need to order a new lower dish rack assemblyPlastic pieces used to make the rack adjustable broke off; ordrng 1 W11544445 (Lower dish rack assembly)"

"Top left RC light is the only light ON when checking DC voltage we have 19.56When checking the light under the top left one only had 8 DC VWhen checking the one on ceiling above the top left light had 6 DC VChange out all of the lights with modules off of Truck stock and there is no difference Then went around and checked voltage again, and the only light that had any power coming out of it was the top left light, which was the jumper from the freezer to the refrigerator compartment. Then from there there was no voltage on any of the other lights. They were all reading zero therefore the wire harness circuit for the refrigerator compartment LED lights are broken, causing the circuit not to be complete and the lights not to work and the inner LED light wire harness inside the cabinet is not serviceable"

Found faulty manifold part order ; ordrng 1 W11652258 (Manifold)

"Found faulty control, Dsi board and igniter part order ; ordrng 1 W11620570 (Control) and 1 W11162730 (Dsi board) and 1 W11524031 (Igniter)"

Fixed freezer gasket.

Replaced worn out idler & supports. ; used 5 Wpw10314173 (Supports) from stock

Replaced control.

Replaced bad drain pump.

Replaced housing & pipe. Unit still making noise. Per Techline the noise is normal operation. SR# 7741579171

NOT A CALLBACK. F8E1 ERROR IS A COMPLETELY DIFF ISSUE. replaced inlet housing/valve. unit tested ok. again advised cust on load size and capacity.

replaced control PCB. per special projects S153EB. unit tested ok.

Diagnosed unit and found leak in the evaporator ordered part covered under 5 year warranty ; ordrng 1 W11035765 (Evaporator) and 1 W10756020 (Compressor)

Customer called me to let me know unit was working called tech line to document File#7741701416

Diagnosed unit and found shorted inverter and bad door seal cust will think about it and call us back

Diagnosed unit and found no functional error or codes unit have a rattle sound checked all screws tub and drum possible outter cavity unit checksnok

Checked unit found broken belt drive ; ordrng 1 341241 (Belt)

Replace part unit tested properly cleaned blower

Checked unit found broken shield an belt is ripping in pieces ; ordrng 1 W11409708 (Shield) and 1 W11239857 (Belt)

Replace part unit tested properly advised customer to replace water filter SR#7741705490

Checked unit found error code for bad Tachometer Missing or Wrong Signal F7E1; ordrng 1 W11026785 (Drive motor)

Replace part unit is now cooling

Replace part unit tested properly advised

Ran diagnostic ordering High voltage components ; ordrng 1 W11610132 (Transformer) and 1 W11596133 (Capacitor) and 1 W11590863 (Magnetron)

Ran diagnostic Ordering replacement parts for Seal system repair ; ordrng 1 W11635510 (Compressor) and 2 W11504415 (8/8.5)s and 2 W11504448 (5/1.8)s and 1 W11546692 (Evaporator) and 2 W11504433 (6/4)s and 1 W11109499 (Drier)

"Ran diagnostic with customer, found issue being kinked line customer advised on monitoring unit"

Adjusted fan blade from heating element. All functions checked ok at this time

"Installed new drum,belt and support. Tested after no abnormal sound. Unit is working as designed"

"Installed new suspension. Tested after, unit is working as designed."

"Installed new water valve. Tested after no leaks, unit is working as designed. Left defective water valve with customer."

Called techline and ran some tests need to replace control boards and interface harness Sr7741703741; ordrng 1 W11445129 (Console) and 1 W11199545 (Filter board) and 1 W11486781 (Control board)

"checked unit, found still has restricted house vent, showed tenant problem, advised tpss future service for same issue is cod , warranty is on unit not house, sr 7741328279"

Interface not functioning properly. Also found inverter board flashing error code and does not always activate compressor. The customer approved all parts orders. Remaining balance 1338.70; ordrng 1 WPW10468940 (User interface) and 1 W10629033 (Inverter) and 1 WP2188820 (Thermistor) and 1 WP2302937 (Top thermistor)

"Issue not related to previous visit. The door gets frozen, so it becomes difficult to open it, but due to too cold temps so I adjusted temps. Dispenser flap is not closing properly. Fixed spring that closes to prevent any ice build-up at dispenser chute. Called 3rd party to inform it is not a recall and was instructed to close out normally"

Door brackets bent out of place would not let the door open all the way. Bent back into place and the door is now opening and closing properly

"Upon arrival, and after diagnosing, I noticed that the icemaker was not dispensing the ice that it would make also, I noticed that the slab of ice was thicker than it should. I submitted a quote to the customer and he will decide later."

Ran diagnostic ordering control ; ordrng 1 W11608056 (Control)

"Ran diagnostic found filter door and housing uneven as well as left door, ordering washers and filter housing assembly ; ordrng 1 W11189600 (Bracket filter) and 1 W11451366 (Filter housing) and 1 W11307147 (Cover filter) and 1 W11483207 (Assembly filter door) and 4 WP487576 (Door hinge washer)s"

"Ran diagnostic replace faulty valve , all functions checked okay, advice customer about machine operation"

"Ran diagnostic ordering spark module, bake burner and gas regulator ; ordrng 1 WP9758078 (Bake burner) and 1 W10898290 (Regulator gas valve) and 1 W11693498 (Spark module)"

Replaced defective suspensions unit is now working properly

Check unit to find customer does not have the correct power to ignite the heating element customer was informed to call her electrician back out to find out why she doesnt have 240 supplying the dryer. Customer is getting 120 from leg one to ground and she is getting 120 from leg two to ground as shes losing amperage when starting the unit she was referred back to her electrician unit is OK

Change unit to five customer is having a long time drive due to exhaust not being connected to the wall. Customer was informed to replace the box that he has and buy the proper hose for proper installation and better dry performances. Technician also ran a exhaust airflow test and unit passed without holes. Unit is OK.

Check unit to find roach infestation and the unit has generated F1E0 and F3E0. Customer was informed of Whirlpools procedure far as proceeding with any repairs unit is voided. All operations are OK.

Order parts ; ordrng 1 W11298479 (Control) and 1 W11212745 (Actuator) and 1 W11227944 (Capacitor)

"Upon arrival I found unit not turning on, I will order control board and console for unit. ; ordrng 1 W11325580 (Console) and 1 W11549931 (ACU)"

asited je unit checked out

asited je unit checkedc ut

checked unit out unit needs to be cleaned then unit will be correct unit checked out

changed out all parts lisred unit checked out

checked unit out cleaned softener dispenser unit is correct now

Order parts ; ordrng 1 W10909685 (Fuse) and 1 Wp8577274 (Thermistor) and 1 Wp3387747 (Heater) and 1 Wp3391914 (Stat) and 1 279973 (Cut off)

"Customer ran two clean cycles with afresh back to back and did one was load after. Like tech line said to do. Ran diagnostics on washer . Only error code was for f0 e2 suds. Ran wash cycle unit was full of suds again. I took pics again and added them to the document no other error codes. Unit washes,spins and drains. Control board has been change twice and ui . Called tech line again Robert Ref # 7741669743"

Reschedule to go back in one week; saved tckt

Replace defected icemaker unit tested OK

Outer glass broke; ordrng 1 W11051158 (Outer door) and 1 W10544145 (Upper trim) and 1 W10481433 (Nameplate) and 2 W10146346 (Screws)s and 2 98008699 (Screws)s and 2 98006726 (Screws)s

found and replaced broken sw

Replaced bad valve & cracked pan.

Checked unit and replaced dented left fresh food door and resealed gasket. Unit checkes ok. Assisted by Tech JP. Talked to Jess at Trade Partners and issued Auth# m1e94r0nl1.5

need cnt; ordrng 1 w11603811 (cnt)

found and cleared buildup on blower wheel and cycled

changed out latch and control unit is correct now

Replaced control box and harness wire.Ran diagnostics and confirmed all components are operating as designed.Customer will monitor the unit over the next 4872 hours to ensure it reaches and maintains desired temperatures.

"if components are still available unit will need transformer, capacitor, mag and diode ; ordrng 1 WP8205812 (MAGNETRON) and 1 WP8205489 (Diode) and 1 8184046 (Transformer) and 1 8183536 (Capacitor)"