Diagnosed dryer not heating. Customer will get clogged air duct cleared for better drying results.

I replaced air diffuser

Replaced control board

"replaced control board - tested, working as normal."

Replace part advised customer to get plumber out to correct line water is coming out of drain line to the home called tech line was advised to tell customer same thing this is not a washer issue but house issue SR#7742293989

Unit needs fill tube; ordrng 1 W11415785 (Fill tube) and 1 W11232485 (Ice maker)

Found faulty control board. Removed and replaced control board and tested.

"Ran diagnostic replace lower harness and drain pump, found a crack in the tub next to the pump, ordering tub assembly Advice customer not to use unit. And cleaf laundry for next visit access ; ordrng 1 W11550891 (Agitator) and 1 W11513244 (Basket assembly) and 1 W11551646 (Locknut) and 1 W11568797 (Filter drain) and 1 WP8533928 (Screw) and 1 W11219115 (Tub) and 1 W11449840 (Gearcase)"

"Ran diagnostic, clicking noise coming from relays , unable to found any other noise. Advice customer about operation and clicking on and off of relays"

Ran diagnostic ordering back burners and infinity switches; ordrng 2 W11171119 (Right/left back burners)s and 2 WP3149404 (Infinity switch)s

"Ran diagnostic replace tub, basket and gearcase assembly, all functions checked okay"

"needs control, and oven elements ; ordrng 1 W11182108 (ELMNT-BAKE) and 1 W10856603 (ELMNT-BROL)"

replaced suspension and tested - working as normal

Ran diagnostic thermistor working properly at the time bin thermistor not replaced

Replaced inner drain hose from pump to back wall. Operations are correct now

"Upon replacing the parts, the unit door was no longer falling to the ground. The hinges have corrected the issue. The unit is working properly as designed."

Need gearcase ; ordrng 1 W11449841 (Gearcase)

Fixed blockage in tube & pinched drain line.

Unit control board isnt working correctly now; ordrng 1 W11116592 (Board)

Ran diagnostics on ice machine. No issues now. Operations are correct at this time

replaced shorted control board and encoder and broken wire harness and faulty drain pump and valve and ran test cycle. test ok

"And diagnostic frost pattern present, ice not getting form, at harvest, lowes temperature readings 33.9F. Advice customer about possible seal system issue, customer will look into to new machine"

Ran diagnostic error f1e2 present when arrived ordering control ; ordrng 1 W11683481 (Cobtrol)

upon arrival went into diagnostics and checked suspension rods and everything looked good advised customer to distribute clothes properly and teached them how to stop the cycle and restart it unit is working as designed

"Upon arrival and after diagnosing, I could not re-create any issue. The unit is working properly as designed."

"replaced burners, igniters, control, and valve. unit still not working. ordering, DSI and harness.; ordrng 1 WPW10511278 (module-spk) and 1 W10519920 (harns-wire)"

"Upon arrival and after diagnosing, I noticed some debris in the drain pump. Once removing the debris, the drain pump began to work properly with no issues. The unit is working properly as designed."

checked unit out power supply was loose made unit right unit checked out

Ran diagnostic replace faulty control electric all functions checked okay

upon arrival customer was washing big blankets causing to get f0e9 code and washer not spinning advise customer to wash those big blankets in a washateria suspension rods are good . unit is working as designed

checked unit and gave estimate for repair. customer will call back if wants repaired. do not order parts yet; ordrng 1 W11735041 (compressor) and 1 W10843121 (filter dryer) and 1 WPW10218037 (evaporator)

Found ice maker making ice slowly. Removed and replaced ice maker assembly. Checked operation and function

Found faulty machine control. Removed and replaced machine control. Checked operation

"replaced ice maker, motor, and selinoid. unit tested ok."

turned on all burners and oven. unit is working and heating as designed. unit tested ok.

"Checked unit and paint internally is completely scratched out, the customer cleaned it with a metal scrub and damaged all the paint, I called tech line and tech line said they destroyed the unit by doing that and will not be repairable, I called their extended warranty and they said to close the ticket and to refer the customer to contact them File#. 7742294445"

Checked unit and control is not working ; ordrng 1 W11613564 (Panel) and 1 W11637583 (Control)

Checked unit and replaced rotor/stator bolt that backed out. Ran auto test cycle and unit checks ok.

replaced broken wire harness and ran test cycle. test ok; used 1 W11643701 (HARNS-WIRE) from stock

Inspected and found compressor running and evaporator fan running but not getting cold Will need to order seal ssytem components ; ordrng 1 W11546692 (Evaporator) and 1 W11557671 (Compressor) and 1 W11109499 (Drier)

"Customer complaint is that the fridge trips breaker around the 10 minute markFound the fridge disconected Reconnected and started my timer, to document how long it would take to trip the breaker I removed the back panel and inspected for any signs of wires shorted out, touching ground. No signs of shorted wiring Took AMP reading and was only getting like 8.8 amps and the breaker size is 20Removed freezer back panel to expose the defrost heater and see if any wiring was touching ground. No shorted wires. During the inspection, unit went into defrost activating the heating element. Uploaded pictures of temperature for documentation Activated ice maker defrost to see if IM was the one causing to trip. No tripping. All good. After all my inspections were concluded i put everything back and reconnected the fridge on the out right behind unit, but this time unknowingly i reconnected it to the lower porrtion of the duplex and thats when it happened....breaker trippedJust to be sure, I reset breaker then switched to upper and unit held no tripping. When i switched back to the lower its when it automatically tripped. Showed customer findings and advised they have builder and or electrician check outlet and circuit. Also provided customet the brreaker check list incase they needed Recap: Found electrical issue on the duplex outlet wher fridge connects to, unit is working properly."

"Per customer, during the initial usage, 1st time use both ovens were being pre heated to 350 and mid cycle Mr heard a 'POP' and then the ovens stopped heating. I tried to enter diagnostics to see if any error codes were detected but the controls were non responsiveAdvised customer I would have to order the controls and during the repair date would have to further investigate if any wire were touching ground potentially causing the power failure and or controls shortage. ; ordrng 1 W11492294 (User Interface) and 1 W11317945 (Appliance Manager) and 1 W11388048 (Appliance Manager) and 2 WP4449751 (Thermostat)s"

Assisted Tech JP

checked unit out ran diagnostics ran compresser and fans at this point unit has normal sounds cust wanted me to replace compresser to make unit quiater called tec line talked wit kelly unit as normal opration at this point ref 7742290691

Rescheduling appointment.; saved tckt

cecked unit out unit needs new diod and cap unit checked out

"Checked unit and everything is working as it's designed, the customer said last time it tripped the breaker was 2 to 3 months ago, I preheat the unit to 350 degree and unit checked ok, I called tech line and documented with them and they said the unit is working as it's designed File#. 7742292131"

Found broken filter cap. ; ordrng 2 W11238395 (Cap)s

"I arrived to the house after the landlord confirmed the appointment in the morning, and when I was there the tenant showed and said how can they schedule an appointment without letting them know, how is the landlord going to confirm not even being here, the tenant said he didn't have time and had to leave ; saved tckt"

"Checked unit and diode was shorted out, I replaced it and unit was still not working and will need capacitor and magnetron ; ordrng 1 W11256462 (Diode) and 1 W10705215 (Capacitor) and 1 W10754299 (Magnetron), used 1 W11256462 (Diode) from stock"

Checked unit panel and control are not working ; ordrng 1 W11613564 (Panel) and 1 W11683480 (Control)

If u dont shut the door 100% and let it click into place properly then the microwave will just flash the lights twice and u have to open door and shut properly and it starts just fine Need to call into Techline and send the video of the customer complaint SR#7742294251Called in to Techline and send the video of how the customer closes the door compared to how it needs to be closed and he did confirm that the reason theyre running into this issue is because the door is being closed in properly the way that the customers are closing it Slowing the hinges down is causing the door not to close 100% therefore once they open and close it again properly. It works good every time.

"Checked unit and the plug from the garbage disposal was not removed all the way, and when the unit drained with junk it would get clogged there, I removed it and it worked fine"

"Upon arrival I replaced the console, after testing unit it is now going through all the cycles, unit is working as designed."

"Checked unit and fuse and thermistor were shorted out, I replaced them and checked ok, I also advised the customer to clean the vent going to the outside because it's completely clogged, and to clean before using the unit again ; used 1 W10909685 (Fuse), and 1 8577274 (Thermistor) from stock"

Pending reschedule ; saved tckt

"Ran diagnostics, documented intermittent pulsating sound from washer. Unable to duplicate. No further work suggested at this time. Referring back to customer service SR-7742290727"

replaced faulty motor capacitor and ran test cycle. test ok; used 1 W11227944 (capacitor) from stock

checked unit and found parts needed for repair are no longer available. called TPB and agent confirmed.SR#7742193356

replaced broken latch assy. and ran test cycle. test ok; used 1 W11670519 (LATCH) from stock

Ran diagnostic ordering replacement slider and clutch assembly. ; ordrng 1 W10734521 (Slider)

"Fan motor, fill pump sensor. Start relay ; ordrng 1 W11126268 (Pump harness) and 1 W11542867 (Pump with sensor) and 1 W11624931 (Over load) and 1 WP2217224 (Start relay)"

f7e1 upon arrival unit not spinning causing clothes to stay wet changed actuator from t/s and now unit is spinning and working as designed ; used 1 W11481722 (actuator) from stock

I replaced the hose and unit checked ok

"The unit went fine on the auto test and if I have one oven on it works fine and if I have them both on it can't hold it the breaker goes off, So problem is the breaker, I referred the customer to get an electrician, unit checked ok"

"Ran diagnostics, attempted hinge repair. Documented findings from stripped bolt making unit non repairable. Referring back to customer service for further action SR-7742294307"

"Ran diagnostics, replaced faulty timer and thermostat. All functions checked ok at this time"

replaced shorted control board per special project#s153eb and ran test cycle. test ok

"Ran diagnostics, reset controls. Unable to duplicate issue. Customer advised on monitoring and possible interference from breaker in home. Unit checked ok at this time"

"Ran diagnostics, customer advised on power issues and restrictions from venting in home. Unit working as designed"

Reconnected valve and checked all function

Aligned the door hing

Play defected LEDS. .SP?W11606409 - Special Project S84638 - Parts and Labor

Order part ; ordrng 1 WPW10544004 (Striker)

checked and cleared drian pump and all function ok

Inspected unit and found front left element not working. Unit is voided due to roaches all over infinite switch and back panel SR 7742263832

"Inspected the unit and found fuse pop, removed clogged on chute, and installed new thermal cutoff from TS. ; used 1 W10900067 (Cutoff tml) from stock"

Inspected the unit and ran diagnostics. I did not find any active error codes. Ran test with techline unit is working as designed SR7742290040

Inspected unit and found that the spark module needs to be replaced.; ordrng 1 W10898291 (Spark module control board) and 1 W11524031 (Oven ignitor) and 1 W10898290 (Gas valve) and 1 W11620561 (Control board)

The customer complained that the unit is taking too long to dry. Inspected the unit and found the dryer duct clogged cleaned out duct and tested after the unit is working as designed

upon arrival changed broken switch door and now unit is closing and starting as designed

all receptacles are melted ordering parts; ordrng 1 W11134595 (receptacle harness) and 2 W11364018 (elements rf Lr)s and 2 W11364019 (element Lf RR)s and 1 3148952 (switch rf lr) and 1 3148954 (switch lf rr)

"upon arrival door is not aligned. the door came off the hinge bolt aligned it back up, unit is now closing and working as designed"

upon arrival unit not starting at all; ordrng 1 W10834731 (control) and 1 W10837402 (sump and motor)

upon arrival start button not working need control; ordrng 1 W11683480 (control)

"Upon arrival I found unit flame not going through the burner, will need to order a manifold assembly, and burners. ; ordrng 1 W11455147 (Burner cap) and 1 W11662402 (Burner kit) and 1 W11730298 (Manifold)"

Customers concern was a crease in the door seal remolded the door seal with heat gun make sure everything is closed and sealed properly all operation. OK unit is operating as a sign now.

"Customers concern was that the dryer was not getting hot enough ran the dryer on the heavy duty cycle and the unit was reaching 170 to 180? which is plenty hot and the vent to their house has never been cleaned. I advised them since they were having issues with multiple cycles to drythat they need to have the vent cleaned out because the moisture is getting trapped inside of the dryer.The unit is operating as designed all operations OKCustomer also had concerns about the dryer door how it is flush at the top and sticks out less than a 1/4 inch at the bottom. The door is not twisted. Everything is straight, but there is no mechanical issue with the door. It is still sealing properly and not causing any issues this falls under cosmetic issue, which is only covered for the first 30 days after purchaseThe unit is operating as designed all operations OK"

Unit throwing F6E6 error code customer said that they had some power surges right before this issue occurredMain control issue need to order the appliance manager; ordrng 1 W11100267 ((AM) Control board)

Replace bad suspension rods all working fine now

Replace defected dispenser working fine no leaks

Check and found that the Control Board was bad needs replacing Customer is just going to replace the dishwasher completely

Fixed door gaskets.

Upon arrival i replaced parts. Unit is no longer in flood mode. I tested ran diagnostic cycle unit completed normally. Functioning normal. Unit is working as designed.

Upon arrival i diagnosed unit. After inspection unit had faulty connection at thermal fuse. I reconnected and secured connection. I tested afterwards unit started functioning normal (picture attached). Unit is working as designed.

Found defected Megatron and capacitor replaced same parts working fine now

Order part reschedule with customer.Replaced clogged bake burner2wgt; ordrng 1 W11590294 (GNTR-OVEN)

part order; ordrng 1 w11613480 (pump)

"Customers complaint is low ice production ran unit through diagnostics, and the recirculation pump was kicking on, but did seem like it was pumping slightly slower than normal there is a service pointer, indicating that the recirculation pump has poor suction, causing the slow ice production; ordrng 1 W11439191. (Recirculating pump) and 1 W10511923 (Bin thermistor)"

Inspected the unit and ran diagnostics; I did not find any error codes. The unit is spinning properly. It is working as designed. It is a load issue. SR 7742292411