Ordering parts ; ordrng 1 W11567409 (Orion board) and 1 W11578205 (Compressor)

Replaced bad water valve and checked operation ok

Order Ui board; ordrng 1 W11478525 (Control)

"found unhooked vent hose from house and dryer working as desighned, advised to check house vent"

"found house vent allowing outside ambient air in causing unit to sweat, refered cust to builder"

need module; ordrng 1 w10475149

need sw; ordrng 1 w10275048 and 1 w10434452

found and replaced new bad part

Need Erc and sensor error codes for both; ordrng 1 W11567348 (Erc) and 1 W10181986 (Sensor)

Installed harness ran test all operation normal

replaced bad capacitor; used 1 W11395618 (CAPACITOR) from stock

2nd man helper call back on DC AND JT.Replaced 3 way valve seal system

"Need gearcase, cam,belt ,wash plate and actuator ; ordrng 1 W10721967 (Cam) and 1 W11449740 (Gearcase) and 1 W10902815 (Wash plate) and 1 W11481722 (Actuator) and 1 W11239757 (Belt)"

Checked unit control is unresponsive not allowing to go into diagnostics ; ordrng 1 W11506011 (Control) and 1 W11460962 (UI panel) and 1 W11460908 (Console) and 1 W11627526 (Jumper wire)

Part order unit with faulty fan motor and evaporator harness.; ordrng 1 W11502499 (Evap harness) and 1 WP2315539 (Motor)

need to order part ; saved tckt

part to be order.; ordrng 1 w11416362 (pump-assembly)

Need board and ui; ordrng 1 W11419171 (Board) and 1 W11700916 (Latch) and 1 W11478526 (Ui)

No water in over flow pan. Drain hose on top of switch. Tie strapped hose above switch and replaced switch. No suds in dishwasher ; used 1 W11545764 (Switch) from stock

"Ran diagnostics, cleared build up from bottom of ice container and customer advised on unit functions. Checked ok at this time"

Replaced diffuser and checked operation of unit ok

replaced shorted control board and wiring harness and leaky drain pump and broken door latch and strike. ck ok

replaced shorted led modules and found shorted wiring in deli door and shorted control board. order parts 2wgt; ordrng 1 W10815668 (dor-fip bl) and 1 WPW10769076 (cntrl-elec)

"Removed all products and shelving from refrigerator. Remove ceiling, air duct riser and refrigerator evaporator cover. Replaced refrigerator fan motor with wiring harness assy. Operations are correct now"

SR# 7739228332 order evaporator fan. ; ordrng 1 W11661931 (Evaporator fan)

Replaced bad bin stat.

Fixed loose connection to control.

"Replaced faulty cam, actuator, and main control. All unit functions checked ok."

Fixed wheel bracket vibrating against cabinet.

"replaced, compressor, evap, tubing and repaired factory leak. evac and recharge. unit is cooling at this time. M1BE6D1NL1.5"

unit needs high voltage repair.; ordrng 1 W11545871 (transformer) and 1 WPW10574736 (capactr-mg) and 1 W11256462 (diode) and 1 W11495561 (magnetron) and 1 W10832024 (thrmst-fix) and 1 W11707984 (fuse)

it was the hose loos.

"Ran diagnostics, cleared off balance errors from memory reset controls and customer advised on proper weight distribution. Unit checked ok"

"Ran diagnostics, ordering complete suspension replacement ; ordrng 1 W11130362 (Suspension)"

Found bad compressor. Evacuated Freon. Removed and replaced compressor and drier. Recharged system and checked

Found drier partially restricted and leaking. Removed and replaced drier. Recharged system and checked

Found freezer door gasket pulling away from door. Put silicone on gasket and reattached gasket to door.

"Ran diagnostics, customer advised on moisture buildup common due to ambient temp settings and adjustment of gaskets. Unit working as designed"

"Ran diagnostics, ordering replacement control assembly ; ordrng 1 W11498190 (Control)"

"Ran diagnostics, ordering replacement fill valve assembly ; ordrng 1 W11595805 (Valve)"

replaced shorted control board and sensor and checked operations. ck ok

Replaced bad pan and hose.

"Replaced control assembly, operations are correct now"

hanged out comtrol checked voltage at mullion unit had voltage reset gascket unit checked out

"Replaced faulty control assembly, all unit functions now checked ok."

Replaced faulty motor and blower wheel. Unit is now working as intended no issues at this time

Will need seal system components. Gave customer a quote and he will not continue with repairs.

When calling customer in the morning she said she no longer needed service.

"Checked unit with tech line and everything is working as it's designed, I explained to the customer on how the unit works and customer was not happy with that, so I referred the customer to contact customer service because customer said that wasn't acceptable with that that the unit gets to hot to the touch File#. 7739231494"

"I replaced the led lights and checked ok, and while I was doing that, the customer kept saying over and over he been having problems with the temperatures since they got the unit, because some time when he opens the doors the temperature in the freezer rises up to 30 degrees, he closes the door and comes back less than 30 minutes and the temperature is back to normal, I explained to the customer I could checked it out but there will be a service call fee, and explained to customer there might not find anything because everything has been working normally since it been there, customer said not to worry and to check it out, I called tech line and the first thing that they told me, that they don't believe the customer complain, that if this customer had an issue with the temperature that has the unit for three years, he should of called long time ago, and that he was just taking advantage of me while I was there, and we did check everything on the unit and everything checked ok, I explained that to the customer and the customer said that wasn't possible and said there is something wrong with the electronics, I explained to him, if he is comfortable I can replace the electronics and give him an estimate on that and the customer said to go ahead, I explained to the customer it was time for him to pay the service call fee, the customer said I was crazy because I haven't done anything to the unit and for me to ask him for money is unacceptable, and to get out of his house, File#. 77392231057"

"Checked unit and there was too much water pressure coming to the unit , I closed a little bit on the valve and checked ok"

Installed new mullion for unit with sweat on linear. Unit running properly.

"Checked unit and dryer vent going to the outside is completely clogged, I advised the customer to fix it before using the unit again, also the unit's gasket is worn out because customer has been over loading unit and clothes dragging on the gasket ; ordrng 1 Xxxxxx (High heat adhesive) and 1 W10906683 (Gasket)"

"Checked unit and everything was working as it's designed, I pulled the unit out a showed the customer on how the unit works"

"Checked unit and freezer door was cracked open and condensation in the unit, I showed the customer the problem and advised them to be careful with the door"

checked unitout unit had oversuds resec control told cust to run clean cycle then unit will be correct unit checked out

checked unit out mag tube was burnt called tec line talked with leon sent picturs in non repairable 7739222767

Replaced noisy motor and checked operation of unit ok

Replace part unit tested properly

Upon arrival I diagnosed unit. After inspection no ice. It only did it once and stop making compressor really hot not on. Called techline to document and send pictures of what was in side lines(pictures attached). Techline unit is not repairable. SR#7738953998.

Upon arrival I replaced parts. After replacement I ran unit everything is working. Ran diagnostic cycle everything passed. I adviced customer of the weight distribution on unit if not distributed causes more noises than usual and can cause damage to unit. As it did with wiring SR#7739134307. No noises Unit is working as designed.

Upon arrival I diagnosed unit. After inspection handle was already installed on unit. I reassured everything was tighten and secured. Handle did not come off. Handle is secured. Unit is working as designed.

"Had error code F7E4 (basket re-engagement) F7E5 (shifter not engaging) will need slider, clutch, rotor and stator motor, and control board. ; ordrng 1 W11614514 (Control board) and 1 W10754448 (Clutch) and 1 W10734521 (Slider) and 1 W11195971 (Stator Motor) and 1 W11260238 (Rotor Motor)"

Replaced bad air damper and checked operation of ok

Inspected and found compressor running and evaporator fan running but not cooling Will order sealed system components ; ordrng 1 W11592010 (ANT Compressor) and 1 W11291123 (Evaporator) and 1 W11109499 (Drier) and 1 W11575001 (3 way valve assembly)

Inspected MW outlet for voltage and did not have any voltage Checked breaker and found it tripped Customer advised there was a storm and soon after that the MW stopped working Reset breaker and checked MW that it heated correctly which it did Unit is now working as designed

"Check unit to find all operations working as designed on arrival. Customer was informed that she is choking the air using the dryer without a exhaust hose going to the outside. There is a picture on the showing. The dryer is being used without a hose. It is pushed all the way back to the wall, not allowing lid to escapeunit is OK. Customer was informed to purchase a exhaust hose."

Order parts ; ordrng 1 W11256462 (Diode) and 1 W10561770 (Capacitor) and 1 W10818686 (Magnetron)

Came out to replace part drain pump is different from pump on unit connection from harness dont fit new pump ; ordrng 1 Xxxxx (Drain pump)

Checked unit only error code stored in unit off balance load advised customer about over loading an pausing the unit when in spin cycle to adjust load for even balance

Picked up data logs returning back to office

Checked unit lid not locking unit not allowing unit to start a cycle ; ordrng 1 W11395618 (Capacitor) and 1 W11513248 (Latch)

Checked unit not powering on ; ordrng 1 W11547180 (Start device) and 1 W11611445 (Harness)

found and replaced worn parts

Replay damage handle

Replace damage handle

Order part and reschedule ; ordrng 1 WPW10366605 (Control)

Found dryer working as design customer has main vent in the wall need to be serviced

Found ui not working replace same part all tested ok

Customer may need main control; ordrng 1 W11532957 (Control)

"Stopped at Leasing office for keys, Leasing agent went with me as kids were at home Ran diagnostics no codes found Inspected washer, properly leveled Advised Management to let tenant know about loading machine to WP specifications Unit is working as designed"

Replaced control board and UI panel

Found fridge door gasket not sealing properly Heated and reshaped gasket to seal properly and prevent moisture buildup Uploaded pictures of before and after for documentation

Replaced vent trim

Replaced parts list but issue continues Will order harness and drain pump ; ordrng 1 W11643701 (Harness) and 1 W11399437 (Drain pump)

"Inspected range oven and was not able to duplicate customer noise complaint Per customer description of noise advised that the MW exhaust venting sometimes makes noises on windy days as the vent opens/closes potentially being the source of the noise and if so, to not be concerned its normal and does not affect the function of the range/oven Burners and oven heating as designed"

Replaced faulty Gearcase and cam. Unit is now working as intended no issues at this time

Per techline adjusted settings to reflect what the customer is after. Clothes will dry on towels cycle so adjusted normal cycle to work more closely to that cycle Sr# 773921975

Replaced faulty thermostat. Unit is now working as intended no issues at this time

Found faulty ice bin and coupling ; ordrng 1 W11347840 (Ice bin) and 1 WP2220458 (Coupling) and 1 WPW10258544 (Shaft) and 1 W10852956 (Spring)

"Ran diagnostics, ordering replacement element and thermal cut off; ordrng 1 280148 (Cutt off) and 1 WP3387747 (Element)"

replaced broken dispenser motor coupling and checked operations. ck ok; used 1 WPW10169511 (COUPLING) from stock

Motor was damaged in box. Busted up; ordrng 1 W11187731 (Motor assy)

Customer could not be reached

NOT ABLE TO REACH CUSTOMER)

Replaced thermal cut off with truck stock ; used 1 W10900067 (Thermal cut off) from stock

Order part and reschedule ; ordrng 1 W11256462 (DIODE)

Upon arrival I diagnosed unit. After inspection upper spray arm lose causing noise. I removed and reinstall upper blade spray arm. After unit is working as designed.

Found loose heater connection

Upon arrival unit was not starting due to strike not engaging latch properly. I adjusted strike and unit is now working as designed.