Replaced bad fuse & broken element.

"Replaced shorted latch, checked operation ok and left old part with consumer"

"W1d4jt1nl2. Installed new motor, and capacitor for unit not starting. Washer operations are now correct."

Need control board; ordrng 1 W11607637 (Board)

"All operations are running properly. Customer has too many products blocking air flow, but still no food freezing abnormally. She stated she wants new refrigerator before warranty ends. Job complete."

"Checked unit to find customer has major roach infestation,,she was informed of whirlpools policy and it would cost out of pocket for further repairsunit is voided due to infestation"

Order parts ; ordrng 1 W11637088 (Control)

Order parts ; ordrng 1 W11465032 (Harness)

"Check unit to find all operations working as designed customer was instructed that when she has a bad low, she can pause the unit and sort the clothes to even out the load and restart the unit suspension garage are good unit is"

Order parts ; ordrng 1 Wp697772 (Wheel) and 1 W11549461 (Motor)

Check you to find customer is getting power from leg one to ground of 124 and leg two to ground is 124 but power going all the way across is zero customer was informed that she needs an electrician unit is OK

Order drain pump; ordrng 1 W11396717 (Drain pump) and 1 W11687817 (Control board) and 1 W11568984 (Harness)

Replaced switches knob

Need Element and switch; ordrng 1 3148954 (switch) and 1 W10248262 (element)

Upon arrival and after replacing the parts the unit no longer made the loud noise and also passed a diagnostic cycle. Unit is now working as designed

"Mid way through the repair after removing the washplate I noticed the basket was badly corroded and broken into pieces. Will the tub, basket, and surrounding parts ; ordrng 1 W11178227 (BASKET) and 1 W11551646 (NUT SPANNER) and 1 W11219115 (TUB) and 1 W11568797 (DRAIN FILTER) and 4 WP8533928 (FILTER SCREW)s"

Upon arrival and after diagnosing I noticed the flames were bright orange. The customer mentioned the home has propane. The range will need to be converted to LP also. Nothing wrong with the unit. Working as designed. SR#7740681886

Wrong color console was sent. Ordering the SS one. ; ordrng 1 W11600370 (CONSOLE SS)

Replaced parts ran; unit had no abnormal sound. Unit working as designed.

Replaced parts ran unit did not hear sound. Unit is working as designed.

"Upon arrival, I inspected the unit and could not duplicate the issue. I quoted the customer for two switch igniters.; ordrng 2 WP3190779 (Switch igniter)s"

"Upon arrival, I inspected the unit and found that the bake element was not working; it will need to be replaced.; ordrng 1 W11567368 (Control board) and 1 W11182108 (Bake element)"

"Upon arrival, I inspected the unit and found no power coming from the extension cord to which the unit was plugged. I got power to the unit, ran diagnostics, and all tests passed; the unit is working as designed."

Replaced faulty control and condenser fan. Unit is now working as intended no issues at this time

Upon arrival i diagnoses unit. After inspection unit will not reset from flood mode. Will need parts order.; ordrng 1 W11607637 (Control Board) and 1 W11665967 (Harness Lower)

"Ran diagnostic ordering ice maker, (icemaker shows discontinued); ordrng 1 Wpl67001557 (Icemaker assembly)"

"Ran diagnostic replace timer, advice customer about calling a duct cleaning company to clear any obstruction at the exhaust line. All functions checked okay"

"Ran diagnost, ic contacted tech line , test, control defrost faulty. Ordering control electric ; ordrng 1 WPW10352689 (Control electric)"

"Ran diagnostic, adjust harness at limit switch, all functions checked okay"

"Ran diagnostic test suspensions, suspensions are bad, ordering suspensions ; ordrng 1 W11130362 (Suspensions)"

"Ran diagnostic, test shock absorber, absorbers are bad, sending quote for approval to replace absorbers; ordrng 4 W11415987 (Shock absorbers)s"

"found and replaced damaged drum, cautioned cust it is a clothes dryer not a shoe dryer"

"found bad house breaker, advised cust needs electrican"

"found drain hose too deep in house drain straining unit , corrected and cycled"

found and replaced shorted parts and cycled

found and replaced shorted parts and cycled

found and replaced shorted parts and cycled

Upon arrival I changed the water valve but after further inspection I found that the water line thats connected to the wall is giving lower water pressure. I contacted Mrs and advised her to get a plumber to look at it and apply more water pressure. Left part with costumer.

"Upon arrival costumer experienced on and off dryer that would work only sometimes. After putting it on diagnotics I saw one error code and its a motor failure, it will be needing a heater element and a motor. ; ordrng 1 279827 (Motor) and 1 279838 (Heater element)"

Replace damage support all OK now

Found appliance management control need recalibrated run service check all tested OK now

Replace gas valve unit tested properly

Replace parts unit tested properly

Replaced bad fan and harness.

Replaced bad drain pump. Unit operating as designed.

Replaced control board

"Arrived to troubleshoot MW Customer had MW plugged to external surge protector and per customer after 10 minutes MW would trip the surge protectorAdvised customer that surge protector do go weak and or bad, she was not hearing it.Checked outlet and per Mrs she had an electrician replace outlet, she showed me old outlet and receipt Uploaded pictures and clearly see that the Original issue is still present (open neutral) Plugged MW to my extension and different circuit and MW worked just fineCustomer still not satisfied wanted me to heat for 10 whole minutes..who heats their food for 10 minutes ??? But just to show the customer I ran for 10 whole minute way MY extension diff circuit and worked just fine. Advised customer to get a certified electrician to check wiring at the MW outlet, Unit is working as designed Called tech support to document, they also concurred unit is working as designed SR# 7740682672"

"Ordering replacement Cam, actuator capacitor ; ordrng 1 W11481722 (Actuator) and 1 W11395618 (Capacitor) and 1 W10721967 (CAM)"

"Ran diagnostic with techline ordering Replacement Halogen bulb, rotate motor, and UI SR-7740687062. ; ordrng 1 W11460596 (UI CONSOLE) and 1 W11676353 (Turn table motor cover) and 1 W10911403 (Turn motor) and 1 W10886919 (Halogen bulb)"

Customer request to be rescheduled ; saved tckt

"Replaced auger, all unit functions checked ok at this time"

Ran diagnostic quoted customer for replacement IM 150.00 and UI 350.00. Customer approved repair ; ordrng 1 WPW10769076 (DELI UI) and 1 W11658802 (IM)

Corrected issue with loose rotor cap. Allunit functions now checked ok.

"Ran diagnostic, corrected issue with loose screws at blower housing. All functions now checked ok"

Unable to contact customer ; O-emld tckt

Sr# 7740688896Control panel not sending power out to the compressor and condenser fan or any of the components need to replace the user board; ordrng 1 W11555877 (Control panel/board)

Installed all parts unit is running like supposed to all operations OK

Dispenser solenoid on the inside came loose from the plastic latch. Replaced the dispenser all operations OK now.

"Replaced the blower fan and the motor, but the dryer is still buzzing very loud due to too much power causing all of the parts in the dryer to over amp and run it twice. The speed customer needs to have electrician fix the power source before use told customer if he uses the appliance before this gets fixed and the dryer breaks again the unit wont be covered by whirlpool."

Installed all parts doors ceiling good now there is no gap all operations OK now

"Vent hood switches are have power going to them, but none of the operations are working. Need to replace the switches with the board inside. NEED PART research for the user switch interface power going into the panel, but the switches are not doing any operations ; ordrng 1 Xxxxxxxxxx (User switch interface)"

washing machine is working as designed customer said wont fill on all cycles tested on 3 different options that she uses the most and both of them are filling up unit is working properly she stated that she thinks the unit isnt repairable and Maytag needs to get her a new washing machine i informed the customer that i wont be doing that

"Ran diagnostics, ordering replacement basket per service pointer ; ordrng 1 W11172199 (Basket)"

"Ran diagnostics, performed sealed system repair in unit. Recharged system. All functions checked ok at this time"

"Ordering, replacement blower and sensor ; ordrng 1 W11107275 (Blower) and 1 W10833885 (Sensor)"

Found blower not operating which is causing magnetron to overheat. Removed obstruction from blower and tested. Unit is working fine

Upon arrival i diagnosed unit. After inspection water fill tube was restricted ice build up. I thawed ice in fill tube. Tested unit. Water coming to icemaker passed. Unit is working as designed.

Upon arrival and after diagnosing I noticed it was getting 240 volts but had a loose neutral wire at the terminal block. Once it was secured the unit had power and functioned as designed. No parts needed.

Need control board; ordrng 1 W11607637 (Board)

"Upon arrival costumer experienced little to not draining water fully from the basket, after vacuuming the drain hose I was able to unclogge it, it is now draining properly."

Upon arrival went to diagnostic connected loose wire to heater advised customer to use rinse aid unit is working as designed.

Unit not being repaired. Closing ticket

Upon arrival and after diagnosing I noticed a loose drain pump wire. Once secured the unit began to drain properly. No parts needed unit is working as designed.

Reinstalled loose connections on control ran test all operations normal.

Upon arrival i diagnosed unit. Drain pump not coming on. After inspection drain harness faulty wire. I repair wire harness and reconnected to pump. I tested unit afterwards. Unit passed. Unit is working as designed.

Upon arrival i diagnosed unit. Noise coming from blower. Removed unit after inspection blower resteicted with debris. I removed debris. Install unit and tested. No more noise. Unit is working as designed.

Diagnosed refrigerator with low ice production. Defrosted frozen ice maker tube blocking fill cycle. Unit now filling properly.

Tech assist for JL

Checked unit and adjusted door latch and releveled uniit. Ran test cycle and unit checks ok.

removed debris from front drum seal and adjusted blower housing and checked operations. ck ok

checked unit out door gascket was rolled not sitting right made unit right unit checked out

Replace gas valve unit tested properly

Closing out Unit got replaced

"Technician arrived at residence spoke to customer with respectK and immediately was attacked on her beliefs of Centerpoint stating that the range is the problem. OK take in consideration and proceeded to check unit which customer refuses for me to turn on gas to check unit and I immediately turned around and said maam I cant check the unit without gas supply if it is a leak so therefore I turn on gas and proceeded normal diagnosis and determine the unit is not leaking gas. It is burning combustion and I proceeded to turn off gas and walk to my truck to call Whirlpool safety and inform safety of my findings which customer wanted technician to wait on builder and shes like I cant believe youre leaving and youre not gonna wait on the builder. Im like maam Im gonna be in my truck on the phone with Whirlpool if he pulls up, you can inform him that Im outside on the phone with Whirlpool which the builder walks up to my truck and proceeded to tell me just how rude Mrs and husband are which that has nothing to do with the reason Im checking the unit. I reported all my finances and informed customer that she could call Whirlpool safety from this point on that the unit is working as designed she proceeds to cuss me out, etc. I ignore the cursing and I moved on to the next customer on my route with her being rude to me. I could have picked up my bag and left the premises, but I did not. I did my job with a CO monitor and she does not like what shes being told and dont wanna take what shes being told because shes saying it is a leak that centerpoint said the unit was the problem and thats it no matter what I said or checked it was not to her satisfactory because she is expecting technician check valves, technician, check, burners, technician, check regulator gas supply oven orifices everything that requires the flow of gas was checked. There is no gas leak on this particular unit unit is OK"

Adjusted door and latch ran test all operations normal.

"Checked unit and the light bulbs in the oven were not working, I took it off and showed it to the customer that it's a normal light bulb and it could be purchased at any hardware store, and it will not be covered, the customer answered if it's a normal light bulb why don't I carry it and pay for it, and the customer moved to the second compliant which was the door from the microwave showing me that the door doesn't close correctly, by slamming the door, I explained to the customer on how the unit works, that it has a monitor switches and the door can't be slammed because it will bounce back, and it will not work just like he described, also it was dirty with a lot of popcorn seeds everywhere and some stuck in the hinges which also makes it hard to close correctly, I showed the customer on how to close the door correctly, the customer said why does he has to do what I was saying, and not use it the way he wants, by showing me how he slammed the door with a lot of force, that I had to step back because I was afraid something was going to break and hit me on my face, the customer just not did it once he did it multiple time wanting to break something, by looking at that, I just referred the customer to contact customer service and started walking out of the house, and the customer followed me all the way to my out to my truck calling me names and insulting me, I called their extended warranty and documented with them File#. 7740591128"

Upon arrival front right burner not igniting. I secured wire in spark module.

I removed moisture in oven by turning on broil element and then turning on bake for 30 min. Unit is no longer tripping breaker.

adjusted burner flames on all burners and checked all operations. ck ok

Reinstalled blower ran test all operations normal.U1d4j11nL2

Found faulty actuator. Removed and replaced actuator. Ran recalibration and tested. ; used 1 W11481722 (Actuator) from stock

Found loose connection at control. Reinstalled loose connection. Unit is now working as intended no issues at this time

adjusted and re-leveled weels to prevent rolling out wen door is opened and installed vibration pads to prevent rattling noise. ck ok; used 2 W11113654 (PAD) from stock

Order parts ; ordrng 1 W11413407 (Housing)

Replaced parts all ops okay unit working good

upon arrival customer advised builder is replacing unit and does not need service any longer.

Replaced faulty bake element. All unit functions checked ok at this time

Replaced terminal block wire kit. Operations are correct now; used 1 279318 (Terminal kit) from stock

Need wiring harness again; ordrng 1 W11643701 (Wiring harness)

"Ran diagnostics, no error codes.operations correct"