Installed new filter for unit not dispensing water. Unit operating properly.

Removed vent obstruction for unit with bad air flow. Dryer operating properly.

"Unit in need of new control (W11513246),harness (W11643701),cam (W10721967), and actuator (W11481722). Customer does not want to proceed with parts."

Installed led light kit (W11632139) for unit with lights not working. Unit operations are now correct.

Ordering vent assembly (W11414073) for unit leaking water out of vent.; ordrng 1 W11414073 (Vent assembly)

Diagnosed dryer with loud noises. Found no errors or noises present. Unit operating properly.

Ordering parts ; ordrng 1 W11536794 (Control) and 1 Wp8273993 (Burner) and 1 W11171119 (Burner)

Need electronics ; ordrng 1 W10833885 (Sensor) and 1 W11339754 (Ui) and 1 W11620582 (Board) and 1 W10860916 (Dsi board)

Talked to customer pre ID door customer will send video of unit today called tech line was advised to order new door SR#7738859652; ordrng 1 W11551458 (Door)

Replace part unit tested properly no water leaks was detected after part was replaced unit tested properly

Replace compressor refilled refrigerant 4.09 oz unit is now cooling

"Replaced warped door handle, all functions normal"

Ordering parts ; ordrng 1 W11580057 (Compressor) and 1 W11109499 (Drier)

Yoder loop separation per tech line. Unit is under product review

Order control and power supply; ordrng 1 W10830278 (Power supply) and 1 W10843055 (Control)

Replaced motor sump assembly and checked operation of unit ok

Assisted tech OY

I secured loose connection at terminal block. Unit is working as designed.

I installed a connector from truck stock. Unit is no longer leaking. ; used 2 8201815 (Connector) from stock

Needs Dryer Top ; ordrng 1 WP8563663 (Dryer Top)

Compressor one clicks and shuts off Will need sealed system ; ordrng 1 W11580057 (Compressor) and 1 W11578004 (Evaporator) and 1 W11109499 (Drier)

I replaced ice maker

Checked unit and replaced door gasket. Ran test cycle and unit checks ok and no leaks detected.

Replaced ui and main board

Replaced control UI

Reconnected main board and reset the system .Reset breaker box

Needbto order part; ordrng 1 W11266006 (Motor control)

Needbto order control switch; ordrng 1 W10418327 (control)

Replaced valve

Aligned drum assembly

Checked unit it is cooling customer will call back if an problem

"Ordering top door due to gasket not sealing issue, and bottom door due to dent in facing.; ordrng 1 LW10648583 (Door) and 1 LW10648584 (Door)"

"Ordering parts for unit not turning on properly, and suspensions now faulty due to basket not spinning properly.; ordrng 1 W11608056 (Control) and 1 W11665968 (Harness) and 1 W11217817 (Suspension) and 1 W10721967 (Cam) and 1 W11611297 (Belt) and 1 W11481722 (Actuator)"

"Checked unit with tech line because the customer kept saying that his smoke detector keeps going off, and they said they called center point, and that they told them, the flame has a little bit of reddish color, and they had some reading of carbon monoxide, and because of that they have to replace the range, and are demanding a new one, tech line said the unit is working as it's designed, and to refer the customer to customer service File #. 7738862661"

Order suspension system; ordrng 1 W11217817 (Suspensions assembly)

Order harness; ordrng 1 W11590868 (Harness(1)) and 1 W11569161 (Harness(0))

"Checked unit, performed function test, all functions normal. Advised flame sensor could have been obstructed to cause electrode to fire continuously, customer will continue to monitor"

Order motor and belt; ordrng 1 W11026785 (Motor) and 1 W11239857 (Belt) and 1 W10721967 (Cam)

Order inner door assembly; ordrng 1 WPW10347597 (Inner plate glass) and 1 W10829001 (Inner glass) and 1 W10853628 (Glass bracket) and 2 W10812024 (Spring)s and 2 W11025615 (Spring clip)s

"Parts no longer available, diagnostic complete"

"Adjusted loose timer connection, all functions normal"

"Received and replaced a used control with a fault code already stored on it, order again. Clear codes. Replace lid lock. Received fault code for motor and shifter. Check @ motor-one winding (2-4)found infinite, order motor. Ran test 3a found shifter faulty AGAIN. Also, unit needs cap. Connector @ cap crumbled when removing, replace wire harness. Unit also needs suspension rods, as these are sticky. Over limit; ordrng 1 W11026785 (Motor) and 1 W11395618 (Cap) and 1 W11095106 (Harness) and 1 W11130362 (Suspension) and 1 W10913953 (Actuator), used 1 W11116592 (Control) from stock, states that autho needed"

Replaced IM and valve. Tested via OBD service test. All good

"Replaced slide, but unit still not closing properly. Cabinet looks overlapped at the area of concern. Almost like it missed the bracket and sank before spray foam set. Unit is unrepairable"

"Found the ignitor, exit thermistor and gas valve solenoid to be defective. Order all 3; ordrng 1 279311 (Ignite) and 1 WPW10328463 (Valve coil) and 1 8557403 (Thermostat)"

Order parts ; ordrng 1 W11416362 (Pump)

"Ran diagnostics, ordering replacement control assembly ; ordrng 1 W11552018 (Control)"

Not sure whats wrong with refrigerator tech line called. No results yet; ordrng 2 W11602886 (Light module)s and 1 W11123941 (Switch)

Replaced the switch to but relay has failed. Order control

Upon arrival I diagnose unit. Unit kept tripping breaker. I reset control board. I did steps according to service pointer. I removed ground wire let temperature rise. Once reached temperature let it settled at a constant temperature for 15min. Restarted unit. Unit is working as designed.

"Ordering replacement tray, ring and support for microwave. Parts covered by manufacturer; ordrng 1 W11367904 (Tray) and 1 W11252182 (Ring) and 1 W11245707 (Support)"

Upon arrival I diagnose unit. Unit kept tripping breaker. I reset control board. I did steps according to service pointer. I removed ground wire let temperature rise. Once reached temperature let it settled at a constant temperature for 15min. Restarted unit. Unit is working as designed.

Check you to find our operations working as designed unit unit is OK no parts are needed for

The customer cancelled the service

Adjusted door catch and retested unit all okay no problems

Adjusted rinse aid door to close properly all ok no problems

Found heater connection loose

Found loose connection Customer also wanted to address discoloration on panel but its not a serviceable part SR#7738865567

Tech to close ticket per office.

adjusted simmer flames on all burners and checked all operations. ck ok

Found unit not powering on at all. Tighten up connection on noise filter and control

Washer door latch not locking even when strike in completely in - removed top reattached loose latch assembly

reattached loose harness connection to heating element - tested operating as normal

"Checked unit and problem is the voltage at the terminal block is wrong, I showed it to the customer and to get an electrician to fix it because they are getting 240 voltage from neutral to L 2, I also adjusted the door latch because it was not closing correctly"

Upon arrival I diagnose unit. Unit kept tripping breaker. I reset control board. I did steps according to service pointer. I removed ground wire let temperature rise. Once reached temperature let it settled at a constant temperature for 15min. Restarted unit. Unit is working as designed.

Customer had previous repair done on dispenser asy. Dispenser does not fit in with washer and could not repair the cover itself as it comes in an asy.Discontinued parts color in chrome shadow.. they do not make anything in chrome shadow anymore. We cannot replace broken dispenser with cover.Made customer aware. Closing ticket for service.

Upon arrival ran diagnostic and the drain pump was not coming on. I then looked under washer and the drain pump connector was not properly connected. I secured it close the lid properly. Retest and unit is now working as designed.

Upon arrival I diagnose unit. After inspection I adjusted door Hinge and clip . After adjustment unit is now working as designed.

Upon arrival I diagnose unit. After inspection lose wire on juction box connected wire. Unit is now coming on.Unit is working as designed.

Upon arrival I diagnose unit. After inspection noise coming from blower. Removed and reinstall unit.Removed lose debris from inside blower.After removal.Unit is working as designed.

Found faulty control part order ; ordrng 1 W11626074 (Control)

Unit didn't have correct voltage at plug. Builder will get electrician.

"Ran diagnostics, corrected issue with power. All functions checked ok. Customer advised on functions"

"Ran diagnostics, documented finding of ongoing issues with techline and customer advised on possible electrical issue in home."

"Ran diagnostics, ordering replacement spark module and igniter ; ordrng 1 W10860916 (Spk module) and 1 Wpw10324262 (Igniter)"

"no issues, the water line was closed, I opened it, ran the self test, all ok."

"On test mode, very little water trickles through, the ice cubes are very thin and wet, needs a new Inlet water valve. ; ordrng 1 W10897719 (Inlet water valve)"

"On test mode, no error codes, the icemaker is working properly, but found water trace on top of the drain pump, gonna order a new drain pump to prevent further problems. ; ordrng 1 W11539855 (Drain pump)"

Dropped off data loggers. Will pick up Monday 4/15; saved tckt

Found bad gasket. ; ordrng 1 W10443320 (Gasket)

SR# 7738841487 per techline replace control again. If unit does not work call techline to replace. ; ordrng 1 W11693128 (Control)

Cleaned unit.

Found food blocking vent in freezer. Rearranged food in freezer and adjusted control. Checked gaskets for leaks.

Needs console ; ordrng 1 W11600370 (Console)

Inspected and found obstruction on blower wheel Removed and retested Working properly now

Replaced oven igniter Tested and heating as designed

"Arrived at customer home to trouble shoot MW sparkingFound no power to unit. Proceeded to check breaker and in doing so, noticed customer cooking in the garage with propane and portable gas stove and had a huge pot going. Did not think nothing of it but did seem odd. Breaker was not tripped and proceeded to inspect interior of MW. There is where I saw signs of water or moisture penetration inside where the controls and heating components are located. There was rust build up signs that it had been happening for extended periods of time. I cannot prove it but my opinion is that they cook with Big pots under the MW for long periods of time therefore steam getting into the interior of cabinet. Tried to advise of findings and they got really upset that I would even bring that up. Tried to explain to them that if Safety team even went forward with repairs if they would continue cooking the same manner it would happen again in couple more months. They were just not willing to listen. I strongly believe it was use n care neglect. Called tech support and documented with same pictures uploaded SR#7738842575 But if Whirlpool decides to move forward with repairs it would take replacing Transformer,magnetron,capacitor,diode,magnetron thermostatNOTE: customer upset at me for noticing and pointing out what has been happening and wants another tech."

Customer complaint was that there is ice buildup on freezer door Inspected and found door not closing properly Also customer had mullion heater turned off Advised to leave on to assist with moisture And to also ensure food in freezer is not obstructed from closing doorUnit is cooling as designed

"Inspected and found low ice production, checked water filter and found it clogged very low water pressure. Advised customer to purchase a certified filter. Found corroded UI board and wires Also torn door gaskets ; ordrng 2 W10846057 (Gaskets)s and 1 W10815674 (Pantry drawer) and 1 WPW10677119 (UI panel) and 1 WPW10675033 (Contol board)"

Replaced vent trim and handle

Order parts reschedule with customer2wgt; ordrng 1 279827 (motor!dryer) and 1 WP694089 (wheel)

Order parts reschedule with customer.Replaced shorted controls and open lower harness.; ordrng 1 W11700916 (LATCH)

Order parts reschedule with customer2 man w/ JP 2wgt; ordrng 1 W11360594 (COMPRESSOR) and 1 W11360589 (CONTRL-BOX) and 1 W10843121 (filter dryer) and 1 W10913906 (coupler) and 1 w10000000 (r600 kit)

Order parts reschedule with customer. Talked to Joe at Tech line and we chedked thermistors ohms and all check ok. He advised to replaced UI and issued SR# 7738650832use authorization # w1asfr1epl1; ordrng 1 W11518204 (CNTRL-ELEC)

bad door will need dl to replace door; ordrng 1 lw11037733

"Found m/w o t r mag, bad and cap/thrmst, replace same parts run service cycles all tested good"

Order part and reschedule ; ordrng 1 W10443320 (GASKET-AP DOOR FZ 36)

Order parts and reschedule ; ordrng 1 W10888661 (CNTRL-ELEC)

Upon arrival I diagnose unit and after inspection. Unit had condensation on freezer door top seal. I will order mullion rail door seal to help with heater on . Doors seals gasket are sealing and sitting flush to unit.; ordrng 1 W10806457 (Gray Mullion Seal door)

Upon arrival I replaced all parts unit came on and is working as designed. The noise complain customer was experience I clean the blower wheel at the back. They had debris in there loose like little pieces of wood and plastics and lint with plastic circles pictures attached.